Ford Explorer is a versatile SUV that has been a popular choice for families, off-roaders, and adventurers for decades. The 2013 model of the Explorer is no exception. However, like any other vehicle, it has its share of electrical issues that can be resolved by checking the fuse box. But where exactly is the 2013 Ford Explorer fuse box located? In this article, we will guide you through finding the fuse box and replacing the blown fuses.
Locating the Fuse Box
The 2013 Ford Explorer has two fuse boxes – one is located under the hood, and the other is inside the passenger compartment. Let's start with the fuse box under the hood.
Under the Hood Fuse Box
The under the hood fuse box is located on the driver's side, near the battery. To access it, you need to open the hood and look for a black plastic cover with a "FUSE BOX" label on it. Once you find it, use a flathead screwdriver or a coin to turn the two locking latches counterclockwise and lift the cover.
Inside, you will see a diagram of the fuses and relays, indicating which fuse corresponds to which electrical component. Use the diagram to identify the fuse that needs to be replaced. You can also use a fuse puller tool, which is located inside the fuse box cover, to remove the fuse.
Passenger Compartment Fuse Box
The passenger compartment fuse box is located on the left side of the instrument panel, below the steering wheel. To access it, you need to open the driver's door and look for a small plastic cover with a "FUSE" label on it. Use a flathead screwdriver or a coin to pry open the cover and reveal the fuse box.
Again, you will see a diagram of the fuses and relays, indicating which fuse corresponds to which electrical component. Use the diagram to identify the fuse that needs to be replaced. You can also use a fuse puller tool, which is located inside the fuse box cover, to remove the fuse.
Replacing Blown Fuses
Now that you have located the fuse box and identified the blown fuse, it's time to replace it. Here are the steps to follow:
Step 1: Turn off the Ignition
Before you start, make sure that the ignition is turned off and the key is removed from the ignition switch. This will prevent any electrical accidents or injuries.
Step 2: Remove the Blown Fuse
Using a fuse puller tool or a pair of pliers, carefully remove the blown fuse from its slot. Make sure to grip the fuse by the plastic body and not the metal prongs, as this can damage the fuse or cause a short circuit.
Step 3: Insert the New Fuse
Take the new fuse and insert it into the slot where the blown fuse was removed. Make sure that the new fuse has the same amperage rating as the blown fuse. You can find the amperage rating on the fuse itself or in the owner's manual.
Step 4: Replace the Cover
Once the new fuse is inserted, replace the cover of the fuse box by pressing it down until it clicks into place. Make sure that the cover is securely fastened to prevent any dust or moisture from entering the fuse box.
Tips for Maintaining Your Ford Explorer's Fuse Box
Prevention is always better than cure. Here are some tips to keep your Ford Explorer's fuse box in good condition:
Tip 1: Check the Fuses Regularly
Make it a habit to check the fuses in your Ford Explorer regularly, especially before long trips or after any electrical issues. This will help you identify any blown fuses early and prevent further damage to your vehicle's electrical system.
Tip 2: Use the Correct Amperage Rating
Always use fuses with the correct amperage rating for your vehicle's electrical system. Using fuses with a higher or lower amperage rating can cause damage to your vehicle's electrical system, including the fuse box.
Tip 3: Keep the Fuse Box Clean and Dry
Make sure that the fuse box is clean and dry at all times. Wipe off any dust or moisture that accumulates on the fuse box cover or inside the fuse box. This will prevent any corrosion or rust that can affect the performance of the fuses and relays.
Conclusion
The 2013 Ford Explorer fuse box is an essential component of the vehicle's electrical system. Knowing its location and how to replace blown fuses can save you time and money on repairs. Always follow the manufacturer's instructions and use the correct amperage rating for your fuses to prevent any damage to your vehicle's electrical system. Regular maintenance and inspection of the fuse box can also help prevent any electrical issues down the road.
Komentar
Posting Komentar